Cisco Certified Internetwork Expert (CCIE certification)
Multiple Choice Questions on CCIE | Objective Questions | CCIE Quiz | MCQ
1 >>Which of the following denotes the correct usage of pins on the RJ-45 connectors at the opposite ends of an Ethernet crossover cable? ?
- (A) 1 to 1
- (B) 1 to 2
- (C) 1 to 3
- (D) 6 to 1
2 >>Which of the following denotes the correct usage of pins on the RJ-45 connectors at the opposite ends of an Ethernet straight-through cable? ?
- (A) 1 to 1
- (B) 1 to 2
- (C) 1 to 3
- (D) 6 to 1
3 >>Which of the following commands must be configured on a Cisco IOS switch interface to disable Ethernet autonegotiation? ?
- (A) no auto-negotiate
- (B) no auto
- (C) Both speed and duplex
- (D) duplex
4 >>Consider an Ethernet crossover cable between two 10/100 ports on Cisco switches. One switch has been configured for 100-Mbps full duplex. Which of the following is true about the other switch? ?
- (A) It will use a speed of 10 Mbps.
- (B) It will use a speed of 100 Mbps.
- (C) It will use a duplex setting of half duplex.
- (D) B and C
5 >>Which of the following Ethernet header type fields is a 2-byte field? ?
- (A) DSAP
- (B) Type (in SNAP header)
- (C) Type (in Ethernet V2 header)
- (D) B and C
6 >>Which of the following standards defines a Fast Ethernet standard? ?
- (A) IEEE 802.1Q
- (B) IEEE 802.3U
- (C) IEEE 802.1X
- (D) IEEE 802.3Z
Multiple Choice Questions on CCIE | CCIE Quiz
7 >>Suppose a brand-new Cisco IOS-based switch has just been taken out of the box and cabled to several devices. One of the devices sends a frame. For which of the following destinations would a switch flood the frames out all ports (except the port upon which the frame was received)? ?
- (A) Broadcasts
- (B) Unknown unicasts
- (C) Multicasts
- (D) All of the above
8 >>Which of the following configuration issues will keep a SPAN session from becoming active? ?
- (A) Misconfigured destination port
- (B) Destination port configured as a trunk
- (C) Destination port shutdown
- (D) Source port configured as a trunk
9 >>Which of the following are rules for SPAN configuration? ?
- (A) SPAN source and destination ports must be configured for the same speed and duplex.
- (B) If the SPAN source port is configured for 100 Mbps, the destination port must be configured for 100 Mbps or more.
- (C) In a SPAN session, sources must consist of either physical interfaces or VLANs, but not a mix of these.
- (D) Remote SPAN VLANs must be in the range of VLAN 1�66.
10 >>What tool is available to reduce the complexity of a modern network infrastructure that has direct impact on both Layer 2 and Layer 3 design? ?
- (A) Spanning Tree Protocol
- (B) Bridge Assurance
- (C) Virtual Switch Design
- (D) Virtual Switching System
11 >>In a Virtual Switch System configuration, what operational component is used to transport Control, Management, and Data Plane traffic between peers? ?
- (A) VPC-Link
- (B) Sham-Link
- (C) Virtual Switch Link
- (D) Port-Channel
12 >>Cisco IOS was expanded so that it could support modern enterprise deployments by moving away from a monolithic architecture to a more modular design model. What is this current version of IOS? ?
- (A) CUOS
- (B) IOS-NG
- (C) LINUX
- (D) IOS-XE
13 >>Assume that VLAN 28 does not yet exist on Switch1. Which of the following commands, issued in the global configuration mode (reached with the configure terminal command) or any of its submodes would cause the VLAN to be created? ?
- (A) vlan 28
- (B) vlan 28 name fred
- (C) switchport vlan 28
- (D) switchport access vlan 28
14 >>Which of the following are advantages of using Private VLANs? ?
- (A) Better LAN security
- (B) IP subnet conservation
- (C) Better consistency in VLAN configuration details
- (D) Reducing the impact of broadcasts on end-user devices
15 >>Which of the following VLANs can be pruned by VTP on an 802.1Q trunk? ?
- (A) 1-1023
- (B) 1-1001
- (C) 2-1001
- (D) 1-1005
16 >>An existing switched network has ten switches, with Switch1 and Switch2 being the only VTPv2 servers in the network. The other switches are all VTPv2 clients and have successfully learned about the VLANs from the VTPv2 servers. The only configured VTP parameter on all switches is the VTP domain name (Larry). The VTP revision number is 201. What happens when a new, already-running VTPv2 client switch, named Switch11, with domain name Larry and revision number 301, connects through a trunk to any of the other ten switches? ?
- (A) No VLAN information changes; Switch11 ignores the VTP updates sent from the two existing VTP servers until the revision number reaches 302.
- (B) The original ten switches replace their old VLAN configuration with the configuration in Switch11.
- (C) Switch11 replaces its own VLAN configuration with the configuration sent to it by one of the original VTP servers.
- (D) Switch11 merges its existing VLAN database with the database learned from the VTP servers, because Switch11 had a higher revision number.
17 >>An existing switched network has ten switches, with Switch1 and Switch2 being the only VTPv3 servers in the network, and Switch1 being the primary server. The other switches are all VTPv3 clients, and have successfully learned about the VLANs from the VTP server. The only configured VTP parameter is the VTP domain name (Larry). The VTP revision number is 201. What happens when an already-running VTPv3 server switch, named Switch11, with domain name Larry and revision number 301, connects through a trunk to any of the other ten switches? ?
- (A) No VLAN information changes; all VTP updates between the original VTP domain and the new switch are ignored.
- (B) The original ten switches replace their old VLAN configuration with the configuration in Switch11.
- (C) Switch11 replaces its old VLAN configuration with the configuration sent to it by one of the original VTP servers.
- (D) None
18 >>Assume that two brand-new Cisco switches were removed from their cardboard boxes. PC1 was attached to one switch, PC2 was attached to the other, and the two switches were connected with a cross-over cable. The switch connection dynamically formed an 802.1Q trunk. When PC1 sends a frame to PC2, how many additional bytes of header are added to the frame before it passes over the trunk? ?
- (A) 0
- (B) 4
- (C) 8
- (D) 26
Multiple Choice Questions on CCIE | CCIE Quiz
19 >>Assume that two brand-new Cisco Catalyst 3560 switches were connected with a cross-over cable. Before the cable was attached, one switch interface was configured with the switchport trunk encapsulation dot1q , switchport mode trunk , and switchport nonegotiate subcommands. Which of the following must be configured on the other switch before trunking will work between the switches? ?
- (A) switchport trunk encapsulation dot1q
- (B) switchport mode trunk
- (C) switchport nonegotiate
- (D) No configuration is required.
Multiple Choice Questions on CCIE | CCIE Quiz
20 >>When configuring trunking on a Cisco router Fa0/1 interface, under which configuration modes could the IP address associated with the native VLAN (VLAN 1 in this case) be configured? ?
- (A) Interface Fa0/1 configuration mode
- (B) Interface Fa0/1.1 configuration mode
- (C) Interface Fa0/1.2 configuration mode
- (D) None of the other answers is correct.
Leave a Reply