• Skip to content
  • Skip to secondary menu
  • Skip to primary sidebar
  • Educational Article
  • Technical Articles
  • Engineering Physics
  • English Grammar
  • Engineering Chemistry

Latest News on Educational and Technical Era

Latest News, Multiple choice Quiz, Technical, educational articles.

Automobile Engineering Quiz | Practice MCQ #mcq.imBooz

December 13, 2019 by Dr. IM Leave a Comment

Download

Multiple Choice Questions on Automobile Engineering | Objective Questions | Automobile Engineering Quiz | MCQ

1 >>If a tyre is designated as 175/65 R14 82 S, then the aspect ratio for the tyre is ?

  • (A) 175
  • (B) 65
  • (C) 14
  • (D) 82

2 >>The valve tappet clearance is measured by ?

  • (A) screw pitch gauge
  • (B) engineering scale
  • (C) feeler gauge
  • (D) vernier caliper

3 >>The basic purpose of tyres is to ?

  • (A) grip the road and provide good traction
  • (B) substitute for springs
  • (C) act as brake
  • (D) none of these

4 >>The specific gravity of petrol is about ?

  • (A) 0.75
  • (B) 0.85
  • (C) 0.95
  • (D) 1.25

 Automobile Engineering Quiz | Automobile Engineering MCQ

5 >>The clutch is located between the transmission and the ?

Download
  • (A) engine
  • (B) rear axle
  • (C) propeller shaft
  • (D) differential

6 >>Which one of the following statement correctly describe the construction of a bevel-gear type differential? ?

  • (A) The drive shafts are splined to the differential carrier.
  • (B) The left side gear and the differential carrier rotate in constant unison.
  • (C) The differential carrier houses differential pinion gears and side gears, each pinion gear meshes with a different side gear.
  • (D) The differential carrier houses differential pinion gears and side gears

7 >>The brake warning light warns the driver of ?

  • (A) water in the master cylinder
  • (B) air in the hydraulic system
  • (C) failure of the primary or secondary circuit of hydraulic system
  • (D) power-brake failure

8 >>Highest useful compression ratio (HUCR) is the highest compression ratio at which the ?

  • (A) engine can run
  • (B) engine gives maximum output
  • (C) engine is most efficient
  • (D) fuel can be used in a test engine without knocking

9 >>In Diesel engines, during suction stroke, —– is drawn in the cylinder. ?

  • (A) air and fuel
  • (B) only fuel
  • (C) only air
  • (D) none of these

Automobile Engineering Quiz | Automobile Engineering MCQ

10 >>The formula for Iso-octane is ?

  • (A) C8H18
  • (B) C7H17
  • (C) C6H18
  • (D) C7H18

11 >>The crankshaft of a typical in-line four cylinder engine has —– balance weights. ?

  • (A) 12
  • (B) 4
  • (C) 16
  • (D) 8

12 >>The function of a governor in automobiles is to ?

  • (A) limit the power
  • (B) limit the vehicle speed
  • (C) maintain constant engine speed
  • (D) maximise the fuel economy

13 >>A petrol that detonates easily is called ?

  • (A) high octane petrol
  • (B) low octane petrol
  • (C) unleaded petrol
  • (D) blended fuel

14 >>The minimum parking brake force is generally —– of gross vehicle mass (GVM). ?

  • (A) 0.05
  • (B) 0.1
  • (C) 0.15
  • (D) 0.2

15 >>Bead wires are made of ?

  • (A) steel
  • (B) copper
  • (C) zinc
  • (D) aluminium

 

16 >>The condition that results in large quantities of HC emission is ?

  • (A) high temperature combustion
  • (B) incomplete combustion
  • (C) low temperature combustion
  • (D) high atmospheric temperature combustion

17 >>A petrol engine of a car develops 125 N-m torque at 2700 r.p.m. The car is driven in second gear having gear ratio of 1.75. The final drive ratio is 4.11. If the overall transmission efficiency is 90%, then the torque available at the driving wheels is ?

  • (A) 8.091 N-m
  • (B) 80.91 N-m
  • (C) 809.1 N-m
  • (D) 8091 N-m

18 >>The advantage of the fuel injection system over the carburetor system is ?

  • (A) improved fuel efficiency
  • (B) improved emission
  • (C) improved power output
  • (D) all of these

19 >>The component of the oil filter that prevents the passage of metal particles and sludge is ?

  • (A) element
  • (B) relief valve
  • (C) check valve
  • (D) case

 Automobile Engineering Quiz | Automobile Engineering MCQ

20 >>Which one of the following statements correctly describes the construction of a planetary gear type differential ? ?

  • (A) The six planetary pinions rotate in constant mesh with the internal gears.
  • (B) One drive shaft is splined to the central gear and the other to the planetary gear.
  • (C) Each planetary pinion gear meshes with both the central gear and the internal gear.
  • (D) The internal gear is fixed to the planetary gear.

Download
Pages: Page 1 Page 2 Page 3 Page 4 Page 5 Page 6 Page 7 Page 8

Filed Under: Competitive Exam Quiz Tagged With: Automobile Engineering Questions and answers, Automobile Engineering questions MCQs with answers, Automobile Engineering Quiz, automobile gk questions, Basic Automobile Engineering objective question, Multiple Choice Questions on Automobile Engineering

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Primary Sidebar

Recent Posts

  • [01] About Python
  • Migraine Cure effective Treatment | Home remedies माइग्रेन जड़ से खत्म
  • Quiet Quitting: potential causes and how to identify
  • What do you know about Superbug? | 2 common superbugs
  • USA NFL Big Updates on NFL concussion protocol changes
  • USA Life: Top 10 affordable place to retirement in USA for Lives
  • 7 Hottest News Anchors in The World | Most beautiful News Anchors
  • PIRLS: Progress in International Reading Literacy Study: 5 Tips
  • TEDS-M: Teacher Education and Development Study in Mathematics: 5 Tips
  • ICILS: International Computer and Information Literacy Study : 7 Tips

Categories

m

  • Log in
  • Entries feed
  • Comments feed
  • WordPress.org

DMCA.com Protection Status

Copyright © 2023 · Magazine Pro on Genesis Framework · WordPress · Log in